Author Topic: Overclocking  (Read 11107 times)

mewtwo

  • Guest
Overclocking
« on: May 25, 2009, 09:41:41 PM »
The Dingoo guys provide a overclocking application which can push the CPU up to 430MHz - unfortunately, it's no a linux binary, but the source comes with it.

utd_grant

  • Guest
Re: Overclocking
« Reply #1 on: May 26, 2009, 03:32:22 PM »
That way lies madness. Just accept the fact that you've got a cheap, relatively slow machine.

UberBigBarney

  • Guest
Re: Overclocking
« Reply #2 on: July 02, 2009, 10:30:28 PM »
Madness is sometimes what that little machine can induce...  :D

Artus Irbe

  • Guest
Re: Overclocking
« Reply #3 on: July 06, 2009, 09:40:29 AM »
Would it be worth investigating though? It could make a hellova differance. If i knew how, it would try it, but i don't. I can see where Utd_Grant is comming from though.

Neverbe

  • Guest
Re: Overclocking
« Reply #4 on: July 17, 2009, 05:22:23 AM »
It work also with the Cnm?

Leven2e

  • Guest
Re: Overclocking
« Reply #5 on: July 17, 2009, 09:35:52 AM »
It work also with the Cnm?
yeah,it work.

Neverbe

  • Guest
Re: Overclocking
« Reply #6 on: July 18, 2009, 05:39:10 PM »
It work also with the Cnm?
yeah,it work.
How it work?
I don't think that it will enable something by bios...what file i must run?
i have to use some commands?

Artus Irbe

  • Guest
Re: Overclocking
« Reply #7 on: July 21, 2009, 02:08:28 PM »
Have you had any luck? 100MHZ might not seem like a lot, when when were talking a third of our processing power added, its quite significant.

jimux

  • Guest
Re: Overclocking
« Reply #8 on: August 28, 2009, 11:33:49 AM »
Power consumption is proportional to the square of the clock speed, as is heat to dissipate.  But I understand that the processor is a 400Mhz run at 330Mhz to conserve battery time.  Are we missing a trick here.  The battery monitor automatically shows when the box is mains attached so a trigger to switch to 400Mhz when attached should be simple.

Leven2e

  • Guest
Re: Overclocking
« Reply #9 on: August 28, 2009, 08:32:04 PM »
simples!!!

mrdeano

  • Guest
Re: Overclocking
« Reply #10 on: August 30, 2009, 08:13:50 PM »
Power consumption is proportional to the square of the clock speed, as is heat to dissipate.  But I understand that the processor is a 400Mhz run at 330Mhz to conserve battery time.  Are we missing a trick here.  The battery monitor automatically shows when the box is mains attached so a trigger to switch to 400Mhz when attached should be simple.
How do we do that then?

jimux

  • Guest
Re: Overclocking
« Reply #11 on: September 02, 2009, 11:02:00 AM »
Step one: identify the code used to monitor the battery level
Step two: obtain the source
Step three: identify the mechanism used to under-clock ( several are published)
Step four: embed calls to speed up when mains is detected and slow down when on battery.
Step 5: recompile

Unhban

  • Guest
Re: Overclocking
« Reply #12 on: September 03, 2009, 10:01:03 AM »
simples!!!
Chuckle! Equally as off topic is this:

http://www.youtube.com/watch?v=iKsSOEto3B0

(apologies to those who aren't able to see UK TV ads).

Unh.

jimux

  • Guest
Re: Overclocking
« Reply #13 on: September 03, 2009, 11:19:28 AM »
Step three was easier than I thought, now to find a way of flagging when plugged in to the mains.

Mijzelf

  • Guest
Re: Overclocking
« Reply #14 on: September 03, 2009, 05:50:24 PM »
I *think* /dev/MiniPC has something to do with it.